Are you ready for your weld test ?
These weld test plates are production samples welded at the same time as the pressure vessel seam is welded.
The test pieces are cut out and systematically destroyed using some highly imaginative techniques,
We mostly we bend them in all directions to see if we can snap them (Bend test, reverse bend and nick breaks)
Sometimes we hit them with pointed bits of hard metal to see how big a dent we can put in it (hardness test)
We like to pin them down and swing a big hammer at it to see how much it slows the hammer down (Impact test)
Pulling it apart until it breaks is also to be recommended (tensile test)
Another bit will be chopped up , and polished so you could eat your breakfast off it, etched with acid and then looked at with a microscope. (macro test)
All of this is done to check the weld really is up to the job, because it wants to be for a pressure vessel.
These tests are the real ‘proof of the pudding’ of a weld but so much has gone into putting the correct weld down to start with.
It’s hard to believe but I had a count up and got to over 260 International Standard documents (ISO xxxx) relating to welding (listed below because its hard to believe)
We know a bit about welding carbon steel pressure vessels because we do it all the time, but scan through the list of ISO documents below and see how much more there is to know – it’s really quite humbling……
| ISO 3677:1992 |
| Filler metal for soft soldering, brazing and braze welding — Designation |
| ISO 5187:1985 |
| Welding and allied processes — Assemblies made with soft solders and brazing filler metals — |
| Mechanical test methods |
| ISO 10564:1993 |
| Soldering and brazing materials — Methods for the sampling of soft solders for analysis |
| ISO 15614-10:2005 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 10: Hyperbaric dry welding |
| ISO 18279:2003 |
| Brazing — Imperfections in brazed joints |
| Standards and projects under the direct responsibility of TC 44/SC 3 Secretariat |
| ISO 544:2003 |
| Welding consumables — Technical delivery conditions for welding filler materials — Type of |
| product, dimensions, tolerances and markings |
| ISO 636:2004 |
| Welding consumables — Rods, wires and deposits for tungsten inert gas welding of non-alloy |
| and fine-grain steels — Classification |
| ISO 1071:2003 |
| Welding consumables – Covered electrodes, wires, rods and tubular cored electrodes for |
| fusion welding of cast iron – Classification |
| ISO 2401:1972 |
| Covered electrodes — Determination of the efficiency, metal recovery and deposition |
| coefficient |
| ISO 2560:2002 |
| Welding consumables — Covered electrodes for manual metal arc welding of non-alloy and |
| fine grain steels — Classification |
| ISO 3581:2003 |
| Welding consumables — Covered electrodes for manual metal arc welding of stainless and |
| heat-resisting steels — Classification |
| ISO 3581:2003/Cor 1:2008 |
| ISO 6848:2004 |
| Arc welding and cutting — Nonconsumable tungsten electrodes — Classification |
| ISO 14171:2002 |
| Welding consumables — Wire electrodes and wire-flux combinations for submerged arc |
| welding of non alloy and fine grain steels – Classification |
| ISO 14172:2003 |
| Welding consumables — Covered electrodes for manual metal arc welding of nickel and nickel |
| alloys – Classification |
| ISO 14172:2003/Cor 1:2004 |
| ISO 14172:2003/Cor 2:2005 |
| ISO 14174:2004 |
| Welding consumables — Fluxes for submerged arc welding — Classification |
| ISO 14175:2008 |
| Welding consumables — Gases and gas mixtures for fusion welding and allied processes |
| ISO 14341:2002 |
| Welding consumables — Wire electrodes and deposits for gas shielded metal arc welding of |
| non alloy and fine grain steels — Classification |
| ISO 15792-1:2000 |
| Welding consumables — Test methods — Part 1: Test methods for all-weld metal test |
| specimens in steel, nickel and nickel alloys |
| ISO 15792-2:2000 |
| Welding consumables — Test methods — Part 2: Preparation of single-run and two-run |
| technique test specimens in steel |
| ISO 15792-3:2000 |
| Welding consumables — Test methods — Part 3: Classification testing of positional capacity |
| and root penetration of welding consumables in a fillet weld |
| ISO 15792-3:2000/Cor 1:2006 |
| ISO 16834:2006 |
| Welding consumables — Wire electrodes, wires, rods and deposits for gas-shielded arc |
| welding of high strength steels — Classification |
| ISO 17632:2004 |
| Welding consumables — Tubular cored electrodes for gas shielded and non-gas shielded |
| metal arc welding of non-alloy and fine grain steels — Classification |
| ISO 17633:2004 |
| Welding consumables — Tubular cored electrodes and rods for gas shielded and non-gas |
| shielded metal arc welding of stainless and heat-resisting steels — Classification |
| ISO 17634:2004 |
| Welding consumables — Tubular cored electrodes for gas shielded metal arc welding of creepresisting |
| steels — Classification |
| ISO 18273:2004 |
| Welding consumables — Wire electrodes, wires and rods for welding of aluminium and |
| aluminium alloys — Classification |
| ISO 18274:2004 |
| Welding consumables — Wire and strip electrodes, wires and rods for fusion welding of nickel |
| and nickel alloys — Classification |
| ISO 18274:2004/Cor 1:2005 |
| ISO 18274:2004/Cor 2:2006 |
| ISO 18275:2005 |
| Welding consumables — Covered electrodes for manual metal arc welding of high-strength |
| steels — Classification |
| ISO 18275:2005/Cor 1:2007 |
| ISO 18276:2005 |
| Welding consumables — Tubular cored electrodes for gas-shielded and non-gas-shielded |
| metal arc welding of high-strength steels — Classification |
| ISO 21952:2007 |
| Welding consumables — Wire electrodes, wires, rods and deposits for gas-shielded arc |
| welding of creep-resisting steels — Classification |
| ISO 24034:2005 |
| Welding consumables — Solid wires and rods for fusion welding of titanium and titanium alloys |
| #NAME? |
| ISO 24034:2005/Amd 1:2008 |
| ISO 24373:2008 |
| Welding consumables — Solid wires and rods for fusion welding of copper and copper alloys — |
| Classification |
| ISO 24598:2007 |
| Welding consumables — Solid wire electrodes, tubular cored electrodes and electrode/flux |
| combinations for submerged arc welding of creep-resisting steels — Classification |
| Standards and projects under the direct responsibility of TC 44/SC 5 Secretariat |
| ISO 4136:2001 |
| Destructive tests on welds in metallic materials — Transverse tensile test |
| ISO 5173:2000 |
| Destructive tests on welds in metallic materials — Bend tests |
| ISO 5178:2001 |
| Destructive tests on welds in metallic materials — Longitudinal tensile test on weld metal in |
| fusion welded joints |
| ISO 9015-1:2001 |
| Destructive tests on welds in metallic materials — Hardness testing — Part 1: Hardness test on |
| arc welded joints |
| ISO 9015-2:2003 |
| Destructive tests on welds in metallic materials — Hardness testing — Part 2: Microhardness |
| testing of welded joints |
| ISO 9016:2001 |
| Destructive tests on welds in metallic materials — Impact tests — Test specimen location, notch |
| orientation and examination |
| ISO 9017:2001 |
| Destructive tests on welds in metallic materials — Fracture test |
| ISO 9018:2003 |
| Destructive tests on welds in metallic materials — Tensile test on cruciform and lapped joints |
| ISO 10675-1:2008 |
| Non-destructive testing of welds — Acceptance levels for radiographic testing — Part 1: Steel, |
| nickel, titanium and their alloys |
| ISO/TR 16060:2003 |
| Destructive tests on welds in metallic materials — Etchants for macroscopic and microscopic |
| examination |
| ISO 17635:2003 |
| Non-destructive testing of welds — General rules for fusion welds in metallic materials |
| ISO 17636:2003 |
| Non-destructive testing of welds — Radiographic testing of fusion-welded joints |
| ISO 17637:2003 |
| Non-destructive testing of welds — Visual testing of fusion-welded joints |
| ISO 17638:2003 |
| Non-destructive testing of welds — Magnetic particle testing |
| ISO 17639:2003 |
| Destructive tests on welds in metallic materials — Macroscopic and microscopic examination of |
| welds |
| ISO 17640:2005 |
| Non-destructive testing of welds — Ultrasonic testing of welded joints |
| ISO 17641-1:2004 |
| Destructive tests on welds in metallic materials — Hot cracking tests for weldments — Arc |
| welding processes — Part 1: General |
| ISO 17641-2:2005 |
| Destructive tests on welds in metallic materials — Hot cracking tests for weldments — Arc |
| welding processes — Part 2: Self-restraint tests |
| ISO/TR 17641-3:2005 |
| Destructive tests on welds in metallic materials — Hot cracking tests for weldments — Arc |
| welding processes — Part 3: Externally loaded tests |
| ISO 17642-1:2004 |
| Destructive tests on welds in metallic materials — Cold cracking tests for weldments — Arc |
| welding processes — Part 1: General |
| ISO 17642-2:2005 |
| Destructive tests on welds in metallic materials — Cold cracking tests for weldments — Arc |
| welding processes — Part 2: Self-restraint tests |
| ISO 17642-3:2005 |
| Destructive tests on welds in metallic materials — Cold cracking tests for weldments — Arc |
| welding processes — Part 3: Externally loaded tests |
| ISO 17643:2005 |
| Non-destructive testing of welds — Eddy current testing of welds by complex-plane analysis |
| ISO 17655:2003 |
| Destructive tests on welds in metallic materials — Method for taking samples for delta ferrite |
| measurement |
| ISO 22825:2006 |
| Non-destructive testing of welds — Ultrasonic testing — Testing of welds in austenitic steels |
| and nickel-based alloys |
| ISO 22826:2005 |
| Destructive tests on welds in metallic materials — Hardness testing of narrow joints welded by |
| laser and electron beam (Vickers and Knoop hardness tests) |
| ISO 23277:2006 |
| Non-destructive testing of welds — Penetrant testing of welds — Acceptance levels |
| ISO 23278:2006 |
| Non-destructive testing of welds — Magnetic particle testing of welds — Acceptance levels |
| ISO 23279:2007 |
| Non-destructive testing of welds — Ultrasonic testing — Characterization of indications in welds |
| Standards and projects under the direct responsibility of TC 44/SC 6 Secretariat |
| ISO 669:2000 |
| Resistance welding — Resistance welding equipment — Mechanical and electrical |
| requirements |
| ISO 693:1982 |
| Dimensions of seam welding wheel blanks |
| ISO 865:1981 |
| Slots in platens for projection welding machines |
| ISO 1089:1980 |
| Electrode taper fits for spot welding equipment — Dimensions |
| ISO 5182:2008 |
| Resistance welding — Materials for electrodes and ancillary equipment |
| ISO 5183-1:1998 |
| Resistance welding equipment — Electrode adaptors, male taper 1:10 — Part 1: Conical fixing, |
| taper 1:10 |
| ISO 5183-2:2000 |
| Resistance spot welding — Electrode adaptors, male taper 1:10 — Part 2: Parallel shank fixing |
| for end-thrust electrodes |
| ISO 5184:1979 |
| Straight resistance spot welding electrodes |
| ISO 5821:1979 |
| Resistance spot welding electrode caps |
| ISO 5822:1988 |
| Spot welding equipment — Taper plug gauges and taper ring gauges |
| ISO 5826:1999 |
| Resistance welding equipment — Transformers — General specifications applicable to all |
| transformers |
| ISO 5827:1983 |
| Spot welding — Electrode back-ups and clamps |
| ISO 5828:2001 |
| Resistance welding equipment — Secondary connecting cables with terminals connected to |
| water-cooled lugs — Dimensions and characteristics |
| ISO 5829:1984 |
| Resistance spot welding — Electrode adaptors, female taper 1 : 10 |
| ISO 5830:1984 |
| Resistance spot welding — Male electrode caps |
| ISO 6210-1:1991 |
| Cylinders for robot resistance welding guns — Part 1: General requirements |
| ISO 7284:1993 |
| Resistance welding equipment — Particular specifications applicable to transformers with two |
| separate secondary windings for multi-spot welding, as used in the automobile industry |
| ISO 7285:1995 |
| Pneumatic cylinders for mechanized multiple spot welding |
| ISO 7286:1986 |
| Graphical symbols for resistance welding equipment |
| ISO 7931:1985 |
| Insulation caps and bushes for resistance welding equipment |
| ISO 8166:2003 |
| Resistance welding — Procedure for the evaluation of the life of spot welding electrodes using |
| constant machine settings |
| ISO 8167:1989 |
| Projections for resistance welding |
| ISO 8205-1:2002 |
| Water-cooled secondary connection cables for resistance welding — Part 1: Dimensions and |
| requirements for double-conductor connection cables |
| ISO 8205-2:2002 |
| Water-cooled secondary connection cables for resistance welding — Part 2: Dimensions and |
| requirements for single-conductor connection cables |
| ISO 8205-3:1993 |
| Water-cooled secondary connection cables for resistance welding — Part 3: Test requirements |
| ISO 8430-1:1988 |
| Resistance spot welding — Electrode holders — Part 1: Taper fixing 1:10 |
| ISO 8430-2:1988 |
| Resistance spot welding — Electrode holders — Part 2: Morse taper fixing |
| ISO 8430-3:1988 |
| Resistance spot welding — Electrode holders — Part 3: Parallel shank fixing for end thrust |
| ISO 8430-3:1988/Cor 1:1990 |
| ISO 9312:1990 |
| Resistance welding equipment — Insulated pins for use in electrode back-ups |
| ISO 9313:1989 |
| Resistance spot welding equipment — Cooling tubes |
| ISO 10656:1996 |
| Electric resistance welding — Integrated transformers for welding guns |
| ISO 10656:1996/Cor 1:2000 |
| ISO 12145:1998 |
| Resistance welding equipment — Angles for mounting spot welding electrodes |
| ISO 12166:1997 |
| Resistance welding equipment — Particular specifications applicable to transformers with one |
| secondary winding for multi-spot welding, as used in the automobile industry |
| ISO 14327:2004 |
| Resistance welding — Procedures for determining the weldability lobe for resistance spot, |
| projection and seam welding |
| ISO 14554-1:2000 |
| Quality requirements for welding — Resistance welding of metallic materials — Part 1: |
| Comprehensive quality requirements |
| ISO 14554-2:2000 |
| Quality requirements for welding — Resistance welding of metallic materials — Part 2: |
| Elementary quality requirements |
| ISO 15609-5:2004 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure specification — Part 5: Resistance welding |
| ISO 15614-12:2004 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 12: Spot, seam and projection welding |
| ISO 15614-13:2005 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 13: Resistance butt and flash welding |
| ISO 17653:2003 |
| Destructive tests on welds in metallic materials — Torsion test of resistance spot welds |
| ISO 17654:2003 |
| Destructive tests on welds in metallic materials — Resistance welding — Pressure test on |
| resistance seam welds |
| ISO 17657-1:2005 |
| Resistance welding — Welding current measurement for resistance welding — Part 1: |
| Guidelines for measurement |
| ISO 17657-2:2005 |
| Resistance welding — Welding current measurement for resistance welding — Part 2: Welding |
| current meter with current sensing coil |
| ISO 17657-3:2005 |
| Resistance welding — Welding current measurement for resistance welding — Part 3: Current |
| sensing coil |
| ISO 17657-4:2005 |
| Resistance welding –Welding current measurement for resistance welding –Part 4: calibration |
| ISO 17657-5:2005 |
| Resistance welding — Welding current measurement for resistance welding — Part 5: |
| Verification of welding current measuring system |
| ISO 18278-1:2004 |
| Resistance welding — Weldability — Part 1: Assessment of weldability for resistance spot, |
| seam and projection welding of metallic materials |
| ISO 18278-2:2004 |
| Resistance welding — Weldability — Part 2: Alternative procedures for the assessment of sheet |
| steels for spot welding |
| ISO 18594:2007 |
| Resistance spot-, projection- and seam-welding — Method for determining the transition |
| resistance on aluminium and steel material |
| ISO 18595:2007 |
| Resistance welding — Spot welding of aluminium and aluminium alloys — Weldability, welding |
| and testing |
| ISO 22829:2007 |
| Resistance welding — Transformer-rectifier for welding guns with integrated transformers — |
| Transformer-rectifier units operating at 1000 Hz frequency |
| Standards and projects under the direct responsibility of TC 44/SC 7 Secretariat |
| ISO/TR 581:2005 |
| Weldability — Metallic materials — General principles |
| ISO 857-1:1998 |
| Welding and allied processes — Vocabulary — Part 1: Metal welding processes |
| ISO 857-2:2005 |
| Welding and allied processes — Vocabulary — Part 2: Soldering and brazing processes and |
| related terms |
| ISO 2553:1992 |
| Welded, brazed and soldered joints — Symbolic representation on drawings |
| ISO 4063:1998 |
| Welding and allied processes — Nomenclature of processes and reference numbers |
| ISO 6520-1:2007 |
| Welding and allied processes — Classification of geometric imperfections in metallic materials – |
| – Part 1: Fusion welding |
| ISO 6520-2:2001 |
| Welding and allied processes — Classification of geometric imperfections in metallic materials – |
| – Part 2: Welding with pressure |
| ISO 6947:1990 |
| Welds — Working positions — Definitions of angles of slope and rotation |
| ISO 9692-1:2003 |
| Welding and allied processes — Recommendations for joint preparation — Part 1: Manual |
| metal-arc welding, gas-shielded metal-arc welding, gas welding, TIG welding and beam |
| welding of steels |
| ISO 9692-2:1998 |
| Welding and allied processes — Joint preparation — Part 2: Submerged arc welding of steels |
| ISO 9692-3:2000 |
| Welding and allied processes — Recommendations for joint preparation — Part 3: Metal inert |
| gas welding and tungsten inert gas welding of aluminium and its alloys |
| ISO 9692-4:2003 |
| Welding and allied processes — Recommendations for joint preparation — Part 4: Clad steels |
| ISO 17658:2002 |
| Welding — Imperfections in oxyfuel flame cuts, laser beam cuts and plasma cuts — |
| Terminology |
| ISO 17659:2002 |
| Welding — Multilingual terms for welded joints with illustrations |
| ISO/TS 17845:2004 |
| Welding and allied processes — Designation system for imperfections |
| ISO/TR 25901:2007 |
| Welding and related processes — Vocabulary |
| Standards and projects under the direct responsibility of TC 44/SC 8 Secretariat |
| ISO 2503:1998 |
| Gas welding equipment — Pressure regulators for gas cylinders used in welding, cutting and |
| allied processes up to 300 bar |
| ISO 3253:1998 |
| Gas welding equipment — Hose connections for equipment for welding, cutting and allied |
| processes |
| ISO 3821:1998 |
| Gas welding equipment — Rubber hoses for welding, cutting and allied processes |
| ISO 5171:1995 |
| Pressure gauges used in welding, cutting and allied processes |
| ISO 5172:2006 |
| Gas welding equipment — Blowpipes for gas welding, heating and cutting — Specifications and |
| tests |
| ISO 5175:1987 |
| Equipment used in gas welding, cutting and allied processes — Safety devices for fuel gases |
| and oxygen or compressed air — General specifications, requirements and tests |
| ISO 7287:2002 |
| Graphical symbols for thermal cutting equipment |
| ISO 7289:1996 |
| Quick-action couplings with shut-off valves for gas welding, cutting and allied processes |
| ISO 7291:1999 |
| Gas welding equipment — Pressure regulators for manifold systems used in welding, cutting |
| and allied processes up to 300 bar |
| ISO 7292:1997 |
| Flowmeter regulators used on cylinders for welding, cutting and allied processes — |
| Classification and specifications |
| ISO 8206:1991 |
| Acceptance tests for oxygen cutting machines — Reproducible accuracy — Operational |
| characteristics |
| ISO 8207:1996 |
| Gas welding equipment — Specification for hose assemblies for equipment for welding, cutting |
| and allied processes |
| ISO 9012:2008 |
| Gas welding equipment — Air-aspirated hand blowpipes — Specifications and tests |
| ISO 9013:2002 |
| Thermal cutting — Classification of thermal cuts — Geometrical product specification and |
| quality tolerances |
| ISO 9090:1989 |
| Gas tightness of equipment for gas welding and allied processes |
| ISO 9539:1988 |
| Materials for equipment used in gas welding, cutting and allied processes |
| ISO 12170:1996 |
| Gas welding equipment — Thermoplastic hoses for welding and allied processes |
| ISO 14112:1996 |
| Gas welding equipment — Small kits for gas brazing and welding |
| ISO 14113:2007 |
| Gas welding equipment — Rubber and plastics hose and hose assemblies for use with |
| industrial gases up to 450 bar (45 MPa) |
| ISO 14114:1999 |
| Gas welding equipment — Acetylene manifold systems for welding, cutting and allied |
| processes — General requirements |
| ISO 15296:2004 |
| Gas welding equipment — Vocabulary — Terms used for gas welding equipment |
| ISO 15615:2002 |
| Gas welding equipment — Acetylene manifold systems for welding, cutting and allied |
| processes — Safety requirements in high-pressure devices |
| ISO 10882-1:2001 |
| Health and safety in welding and allied processes — Sampling of airborne particles and gases |
| in the operator’s breathing zone — Part 1: Sampling of airborne particles |
| ISO 10882-2:2000 |
| Health and safety in welding and allied processes — Sampling of airborne particles and gases |
| in the operator’s breathing zone — Part 2: Sampling of gases |
| ISO 15011-1:2002 |
| Health and safety in welding and allied processes — Laboratory method for sampling fume |
| and gases generated by arc welding — Part 1: Determination of emission rate and sampling |
| for analysis of particulate fume |
| ISO 15011-2:2003 |
| Health and safety in welding and allied processes — Laboratory method for sampling fume |
| and gases generated by arc welding — Part 2: Determination of emission rates of gases, |
| except ozone |
| ISO 15011-4:2006 |
| Health and safety in welding and allied processes — Laboratory method for sampling fume |
| and gases — Part 4: Fume data sheets |
| ISO/TS 15011-5:2006 |
| Health and safety in welding and allied processes — Laboratory method for sampling fume |
| and gases — Part 5: Identification of thermal-degradation products generated when welding |
| or cutting through products composed wholly or partly of organic materials |
| ISO 15012-1:2004 |
| Health and safety in welding and allied processes — Requirements testing and marking of |
| equipment for air filtration — Part 1: Testing of the separation efficiency for welding fume |
| ISO 15012-2:2008 |
| Health and safety in welding and allied processes — Requirements, testing and marking of |
| equipment for air filtration — Part 2: Determination of the minimum air volume flow rate of |
| captor hoods and nozzles |
| ISO 17846:2004 |
| Welding and allied processes — Health and safety — Wordless precautionary labels for |
| equipment and consumables used in arc welding and cutting |
| Standards and projects under the direct responsibility of TC 44/SC 10 Secretariat |
| ISO 3834-1:2005 |
| Quality requirements for fusion welding of metallic materials — Part 1: Criteria for the |
| selection of the appropriate level of quality requirements |
| ISO 3834-2:2005 |
| Quality requirements for fusion welding of metallic materials — Part 2: Comprehensive quality |
| requirements |
| ISO 3834-3:2005 |
| Quality requirements for fusion welding of metallic materials — Part 3: Standard quality |
| requirements |
| ISO 3834-4:2005 |
| Quality requirements for fusion welding of metallic materials — Part 4: Elementary quality |
| requirements |
| ISO 3834-5:2005 |
| Quality requirements for fusion welding of metallic materials — Part 5: Documents with which |
| it is necessary to conform to claim conformity to the quality requirements of ISO 3834-2, ISO |
| 3834-3 or ISO 3834-4 |
| ISO 3834-5:2005/Cor 1:2007 |
| ISO/TR 3834-6:2007 |
| Quality requirements for fusion welding of metallic materials — Part 6: Guidelines on |
| implementing ISO 3834 |
| ISO 5817:2003 |
| Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding |
| excluded) — Quality levels for imperfections |
| ISO 5817:2003/Cor 1:2006 |
| ISO 10042:2005 |
| Welding — Arc-welded joints in aluminium and its alloys — Quality levels for imperfections |
| ISO 10042:2005/Cor 1:2006 |
| ISO 13916:1996 |
| Welding — Guidance on the measurement of preheating temperature, interpass temperature |
| and preheat maintenance temperature |
| ISO 13918:2008 |
| Welding — Studs and ceramic ferrules for arc stud welding |
| ISO 13919-1:1996 |
| Welding — Electron and laser-beam welded joints — Guidance on quality levels for |
| imperfections — Part 1: Steel |
| ISO 13919-2:2001 |
| Welding — Electron and laser beam welded joints — Guidance on quality levels for |
| imperfections — Part 2: Aluminium and its weldable alloys |
| ISO 13920:1996 |
| Welding — General tolerances for welded constructions — Dimensions for lengths and angles |
| ISO 14555:2006 |
| Welding — Arc stud welding of metallic materials |
| ISO 14744-1:2008 |
| Welding — Acceptance inspection of electron beam welding machines — Part 1: Principles |
| and acceptance conditions |
| ISO 14744-2:2000 |
| Welding — Acceptance inspection of electron beam welding machines — Part 2: Measurement |
| of accelerating voltage characteristics |
| ISO 14744-3:2000 |
| Welding — Acceptance inspection of electron beam welding machines — Part 3: Measurement |
| of beam current characteristics |
| ISO 14744-4:2000 |
| Welding — Acceptance inspection of electron beam welding machines — Part 4: Measurement |
| of welding speed |
| ISO 14744-5:2000 |
| Welding — Acceptance inspection of electron beam welding machines — Part 5: Measurement |
| of run-out accuracy |
| ISO 14744-6:2000 |
| Welding — Acceptance inspection of electron beam welding machines — Part 6: Measurement |
| of stability of spot position |
| ISO 15607:2003 |
| Specification and qualification of welding procedures for metallic materials — General rules |
| ISO 15607:2003/Cor 1:2005 |
| ISO/TR 15608:2005 |
| Welding — Guidelines for a metallic materials grouping system |
| ISO 15609-1:2004 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure specification — Part 1: Arc welding |
| ISO 15609-1:2004/Cor 1:2005 |
| ISO 15609-2:2001 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure specification — Part 2: Gas welding |
| ISO 15609-3:2004 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure specification — Part 3: Electron beam welding |
| ISO 15609-4:2004 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure specification — Part 4: Laser beam welding |
| ISO 15610:2003 |
| Specification and qualification of welding procedures for metallic materials — Qualification |
| based on tested welding consumables |
| ISO 15611:2003 |
| Specification and qualification of welding procedures for metallic materials — Qualification |
| based on previous welding experience |
| ISO 15612:2004 |
| Specification and qualification of welding procedures for metallic materials — Qualification by |
| adoption of a standard welding procedure |
| ISO 15613:2004 |
| Specification and qualification of welding procedures for metallic materials — Qualification |
| based on pre-production welding test |
| ISO 15614-1:2004 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel |
| alloys |
| ISO 15614-1:2004/Cor 1:2005 |
| ISO 15614-1:2004/Amd 1:2008 |
| ISO 15614-2:2005 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 2: Arc welding of aluminium and its alloys |
| ISO 15614-2:2005/Cor 1:2005 |
| ISO 15614-3:2008 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 3: Fusion welding of non-alloyed and low-alloyed cast irons |
| ISO 15614-4:2005 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 4: Finishing welding of aluminium castings |
| ISO 15614-4:2005/Cor 1:2007 |
| ISO 15614-5:2004 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 5: Arc welding of titanium, zirconium and their alloys |
| ISO 15614-6:2006 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 6: Arc and gas welding of copper and its alloys |
| ISO 15614-7:2007 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 7: Overlay welding |
| ISO 15614-8:2002 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 8: Welding of tubes to tube-plate joints |
| ISO 15614-11:2002 |
| Specification and qualification of welding procedures for metallic materials — Welding |
| procedure test — Part 11: Electron and laser beam welding |
| ISO 15616-1:2003 |
| Acceptance tests for CO2-laser beam machines for high quality welding and cutting — Part 1: |
| General principles, acceptance conditions |
| ISO 15616-2:2003 |
| Acceptance tests for CO2-laser beam machines for high quality welding and cutting — Part 2: |
| Measurement of static and dynamic accuracy |
| ISO 15616-3:2003 |
| Acceptance tests for CO2-laser beam machines for high quality welding and cutting — Part 3: |
| Calibration of instruments for measurement of gas flow and pressure |
| ISO 15620:2000 |
| Welding — Friction welding of metallic materials |
| ISO/TS 17477:2003 |
| Acceptance tests for CO2-laser beam machines for welding and cutting using 2D moving |
| optics type |
| ISO 17652-1:2003 |
| Welding — Test for shop primers in relation to welding and allied processes — Part 1: General |
| requirements |
| ISO 17652-2:2003 |
| Welding — Test for shop primers in relation to welding and allied processes — Part 2: Welding |
| properties of shop primers |
| ISO 17652-3:2003 |
| Welding — Test for shop primers in relation to welding and allied processes — Part 3: Thermal |
| cutting |
| ISO 17652-4:2003 |
| Welding — Test for shop primers in relation to welding and allied processes — Part 4: |
| Emission of fumes and gases |
| ISO 17660-1:2006 |
| Welding — Welding of reinforcing steel — Part 1: Load-bearing welded joints |
| ISO 17660-2:2006 |
| Welding — Welding of reinforcing steel — Part 2: Non load-bearing welded joints |
| ISO 17662:2005 |
| Welding — Calibration, verification and validation of equipment used for welding, including |
| ancillary activities |
| ISO/TR 17663:2001 |
| Welding — Guidelines for quality requirements for heat treatment in connection with welding |
| and allied processes |
| ISO/TR 17671-1:2002 |
| Welding — Recommendations for welding of metallic materials — Part 1: General guidance for |
| arc welding |
| ISO/TR 17671-2:2002 |
| Welding — Recommendations for welding of metallic materials — Part 2: Arc welding of ferritic |
| steels |
| ISO/TR 17671-3:2002 |
| Welding — Recommendations for welding of metallic materials — Part 3: Arc welding of |
| stainless steels |
| ISO/TR 17671-4:2002 |
| Welding — Recommendations for welding of metallic materials — Part 4: Arc welding of |
| aluminium and aluminium alloys |
| ISO/TR 17671-5:2004 |
| Welding — Recommendations for welding of metallic materials — Part 5: Welding of clad |
| steels |
| ISO/TR 17671-6:2005 |
| Welding — Recommendations for welding of metallic materials — Part 6: Laser beam welding |
| ISO/TR 17671-7:2004 |
| Welding — Recommendations for welding of metallic materials — Part 7:Electron beam |
| welding |
| ISO/TR 17844:2004 |
| Welding — Comparison of standardised methods for the avoidance of cold cracks |
| ISO/TR 20172:2006 |
| Welding — Grouping systems for materials — European materials |
| ISO/TR 20173:2005 |
| Welding — Grouping systems for materials — American materials |
| ISO/TR 20174:2005 |
| Welding — Grouping systems for materials — Japanese materials |
| ISO 22827-1:2005 |
| Acceptance tests for Nd:YAG laser beam welding machines — Machines with optical fibre |
| delivery — Part 1: Laser assembly |
| ISO 22827-2:2005 |
| Acceptance tests for Nd:YAG laser beam welding machines — Machines with optical fibre |
| delivery — Part 2: Moving mechanism |
| Standards and projects under the direct responsibility of TC 44/SC 11 Secretariat |
| ISO 9606-1:1994 |
| Approval testing of welders — Fusion welding — Part 1: Steels |
| ISO 9606-1:1994/Amd 1:1998 |
| ISO 9606-2:2004 |
| Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
| ISO 9606-3:1999 |
| Approval testing of welders — Fusion welding — Part 3: Copper and copper alloys |
| ISO 9606-4:1999 |
| Approval testing of welders — Fusion welding — Part 4: Nickel and nickel alloys |
| ISO 9606-5:2000 |
| Approval testing of welders — Fusion welding — Part 5: Titanium and titanium alloys, |
| zirconium and zirconium alloys |
| ISO 14731:2006 |
| Welding coordination — Tasks and responsibilities |
| ISO 14732:1998 |
| Welding personnel — Approval testing of welding operators for fusion welding and of |
| resistance weld setters for fully mechanized and automatic welding of metallic materials |
| ISO 15618-1:2001 |
| Qualification testing of welders for underwater welding — Part 1: Diver-welders for hyperbaric |
| wet welding |
| ISO 15618-2:2001 |
| Qualification testing of welders for underwater welding — Part 2: Diver-welders and welding |
| operators for hyperbaric dry welding |
| Standards and projects under the direct responsibility of TC 44/SC 12 Secretariat |
| ISO 5179:1983 |
| Investigation of brazeability using a varying gap test piece |
| ISO 9453:2006 |
| Soft solder alloys — Chemical compositions and forms |
| ISO 9454-1:1990 |
| Soft soldering fluxes — Classification and requirements — Part 1: Classification, labelling and |
| packaging |
| ISO 9454-2:1998 |
| Soft soldering fluxes — Classification and requirements — Part 2: Performance requirements |
| ISO 9455-1:1990 |
| Soft soldering fluxes — Test methods — Part 1: Determination of non-volatile matter, |
| gravimetric method |
| ISO 9455-2:1993 |
| Soft soldering fluxes — Test methods — Part 2: Determination of non-volatile matter, |
| ebulliometric method |
| ISO 9455-3:1992 |
| Soft soldering fluxes — Test methods — Part 3: Determination of acid value, potentiometric and |
| visual titration methods |
| ISO 9455-5:1992 |
| Soft soldering fluxes — Test methods — Part 5: Copper mirror test |
| ISO 9455-6:1995 |
| Soft soldering fluxes — Test methods — Part 6: Determination and detection of halide |
| (excluding fluoride) content |
| ISO 9455-8:1991 |
| Soft soldering fluxes — Test methods — Part 8: Determination of zinc content |
| ISO 9455-9:1993 |
| Soft soldering fluxes — Test methods — Part 9: Determination of ammonia content |
| ISO 9455-10:1998 |
| Soft soldering fluxes — Test methods — Part 10: Flux efficacy tests, solder spread method |
| ISO 9455-11:1991 |
Leave a Reply
Want to join the discussion?Feel free to contribute!